Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Gresham Homeowners
Chimney problems in Gresham rarely announce themselves. A cracked crown, a rusted cap, or a liner that’s started pulling apart usually shows up as a slow drip, a faint smell in the living room, or water staining the firebox after a wet stretch off the Cascades. Left alone, a small repair turns into a rebuild. That’s where we come in.
Our technicians have up to 14 years of experience, and they focus only on chimneys, not on second jobs between other work. Every repair starts with an inspection so you can see what’s actually wrong, and most repair jobs around Gresham can be scheduled same-day. Call (833) 538-5519. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Gresham Chimney Sweep is a full-service chimney specialist. We handle chimney sweep and chimney inspection alongside chimney repair, so a problem found during a sweep gets fixed by the same team, not handed to a contractor who’s never been on your roof.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a cover over the flue and top of your chimney, and it’s the first job when you’re trying to keep rain and debris out of a flue. In Gresham’s wet months, an open flue lets water run straight down to the smoke shelf and firebox, and it gives birds and squirrels an easy opening. The right cap also acts as a spark arrestor, which matters for wood-burning homes along the tree-lined streets near Main Street. We install caps and covers made from Famco, Gelco, and Copperfield components, matched to your flue size and chimney construction. Typical installed cost runs $300 – $750, and the written estimate is what sets the final price.
Choosing the Right Cap
A single-flue cap is a simple cover; a multi-flue cap is a larger top that spans the whole crown. Getting that sizing wrong leaves gaps where rain and animals still get in, so we measure the flue first. Stainless construction tends to outlast painted steel in this climate.
Matching the Cap to Your Chimney
Masonry chimneys and factory-built flues use different cap styles, and the wrong one can block draft or fail to seal to the crown. We match the cap to what’s actually on your roof, not to what’s easiest to carry up the ladder. Draft matters too: a cap that sits too low over the flue can push smoke back down.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement means removing an old, damaged, or missing cap and fitting a new one in its place. It’s the job most Gresham homeowners put off, because the old cap doesn’t look that bad from the ground. But a rusted or loose cap lets water creep in at the flue seam, and a cap knocked loose by wind no longer seals at all. When we’re on the roof for a sweep, we check the cap’s fasteners and the seam where it meets the crown, since a cap that’s still attached can still be letting water past. Replacing a cap with Famco, Gelco, or Copperfield components typically runs $250 – $650, depending on the size and whether the flue is single or multi.
When a Cap Actually Needs Replacing
If it’s rusted through, dented, or won’t sit flush on the crown, replacement beats patching. A missing spark screen alone is worth addressing before the next burn season. Small fixes like a loose fastener are usually settled during the same visit.
Working Around Old Chimney Tops
Older caps sometimes sit on cracked mortar, and prying one off can take a piece of the crown with it. We check the crown condition before we pull a cap and repair any loose material as part of the job. That stops you from paying twice.
Chimney Liner Installation
Chimney Liner Installation means fitting a new flue liner, the pipe or clay layer that carries smoke and gases safely up and out of the house. It’s needed when a liner is cracked, unlined from an old installation, or the wrong size for the appliance. In Gresham, older homes near the downtown core are the ones most likely to have clay liners with hairline cracks after winters of freeze and thaw, and a gas insert retrofitted into an unlined flue is another common trigger. We install DuraFlex flexible liner systems, the professional standard for relined chimneys, sized to your appliance. Liner installation typically runs $2,800 – $5,500 depending on height, flue diameter, and the appliance served, with a written estimate before any work begins.
When Relining Makes Sense
A cracked clay liner lets carbon monoxide and heat reach the framing of the house, so it’s a real safety issue, not a cosmetic one. Relining is also standard when you change appliances, like moving from wood to a high-efficiency gas insert. Our technicians inspect the flue with a camera first so the relining decision is based on what’s actually there.
Flexible Liner vs. Rigid Liner
Flexible liners navigate offsets and bends in older chimneys that rigid liner can’t follow. DuraFlex systems are engineered for that kind of routing and still provide a continuous, sealed flue. Rigid sections can be right for a straight, square-block chase, which we identify during inspection.
Chimney Flashing Repair
Chimney Flashing Repair addresses the metal or membrane seal where the chimney meets the roof, which is where a lot of leaks in Gresham actually start. Flashing is the angled metal that sheds water off the chimney’s base and back into the roof, and once it pulls away, water gets in at the joint instead of running past. Most flashing problems show up after a wet season, with stains on the ceiling near the chimney or water appearing in the firebox. We repair and replace flashing using proper step and counter-flashing, matched to the roof material, and we reseal the joints so the repair lasts. Flashing repair typically runs $400 – $900, depending on the roof pitch and how much of the flashing has to be rebuilt.
How to Spot a Flashing Problem
Look for rusted flashing, lifted metal edges, or dark staining on the chimney’s exterior brick near the roofline. Inside, a water stain on the ceiling that lines up with the chimney is the classic sign. An inspection confirms whether the source is the flashing or something else, like a bad crown.
Why Pitch Matters
Steeper roofs need different flashing profiles to shed water properly, and a one-size sealant job won’t hold on a steeper pitch. We cut and fit metal to the actual roof line, not to a standard template. A correct flashing repair also protects the decking beneath it.
Chimney Crown Repair
Chimney Crown Repair fixes the concrete or masonry top that caps the chimney and sheds water away from its walls. It’s needed whenever the crown is cracked, spalling, or pulling away from the flue, which lets water run down into the chimney body and the framing around it. Gresham’s freeze-and-thaw cycle is hard on crowns, and hairline cracks widen over a few winters. We repair crowns by cleaning out the damaged material and rebuilding the sloped surface so water runs off instead of pooling. Crown repairs typically cost $350 – $800, and badly damaged crowns may need a full rebuild rather than a patch, which we’ll tell you straight.
Rebuilding vs. Resurfacing
A shallow crack can sometimes be resurfaced and sealed with a proper crown coating. Deep, structural cracking that reaches the flue usually calls for a rebuild. We check for water damage underneath before deciding, because a patch over wet substrate won’t hold.
Water and the Crown
The crown’s entire job is to keep water away from the masonry below. Once it fails, the path is straight into the chimney’s walls, the firebox, and eventually the framing. That’s why a small crown repair is often cheaper than the water damage it prevents.
Chimney Repair Companies
Chimney Repair Companies are the specialists you call when you need the sweep, inspection, and repair work done by people who do chimney work full-time. It’s the choice between a general contractor who also does a bit of chimney work and a specialist who works on flues, crowns, caps, and liners weekly. Gresham Chimney Sweep is a chimney-only business: sweep, inspection, and repair under one roof, using professional-grade products from DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield. That means the same team identifies the problem and fixes it, without a handoff. Repair work is priced per job by written estimate, with typical repairs running $250 – $5,500 depending on scope, and estimates are free.
What Specialists Bring to a Roof
Specialists already know how a flue offsets, how flashing should meet a specific roof, and what a crown looks like before it fails. That background saves homeowners from trial-and-error outsourcing. Our technicians have up to 14 years of experience in this trade.
What a Repair Estimate Should Include
A written estimate should list the specific repairs, the materials used, and what’s not included. If it doesn’t name the products, ask why. Ours names DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, or Copperfield as appropriate, so you know what’s going on your chimney.
Chimney Masonry Repair
Chimney Masonry Repair restores the brick, mortar, and stone that make up the chimney’s exterior. It’s called for when mortar joints are crumbling, bricks are spalling, or the chimney is taking on water, which is the case on many older Gresham homes after several wet winters. Repointing and rebuilding the masonry keeps water out and keeps the chimney structurally sound. We tuck-point the joints, replace damaged bricks, and seal the surface where appropriate, using matching materials. Masonry repairs typically run $600 – $3,500, depending on how much of the chimney is affected, with larger jobs scoped in a free estimate. For more on how we handle structural fixes, see our chimney repair service.
Why Mortar Fails Here
Freeze-and-thaw cycles push water into small cracks, and then the water expands and pushes mortar loose. The result is crumbling joints and, eventually, loosened bricks. Repointing early stops the cycle before the structure is affected.
Materials That Match the Original
Matching mortar color and brick type matters if you care about how the chimney looks from the street. We match texture and color so repairs don’t stand out. That’s also a sign of a repair done by someone who works on masonry, not just filler over a problem.
Brands We Service
DuraFlex flexible liner systems are what we install for relining work, and we know where they wear, how they route through bends and offsets, and how to size them correctly for the appliance. Olympia Chimney components are used for caps and venting, and working with them regularly means we understand how those parts fit standard flue sizes.
HeatShield is the specialist resurfacing system we use to restore a damaged liner where a full reline isn’t needed, and it’s a repair option many sweep-only companies can’t offer. Gelco, Famco, and Copperfield components cover caps, covers, and ventilation parts, so a repair addresses the whole system, not just the flue. Whether you have DuraFlex, Olympia Chimney, HeatShield, Gelco, Famco, Copperfield, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water stains or a drip near the chimney. A stain on the ceiling or the firebox wall usually traces to flashing, a bad crown, or a missing cap. Left alone, water rots framing and stains masonry.
- A strong creosote smell or visible buildup. Creosote in the flue is the fuel for a chimney fire. A sweep removes it, and if the buildup is heavy, an inspection should follow.
- Crumbling mortar or spalling brick. Loose mortar means water is finding its way in. Repointing now is cheaper than rebuilding a chimney later.
- Smoke spilling into the room. Draft problems can be a cap, a flue obstruction, or a liner issue. A camera and inspection settles which.
- A missing or rusted cap. An open flue lets in rain and animals. A cap replacement is a small job, but the water damage it prevents isn’t.
Our Process, Step by Step
- 1
Inspection first. We start with a camera inspection of the flue, the crown, the cap, and the flashing so we know what’s actually wrong. You get a photo report so you can see the evidence for yourself.
- 2
Written estimate. We quote the specific repairs, the materials, and anything that can safely wait. The written estimate sets the final price, and it’s free.
- 3
Scheduled work. We book the repair and confirm what’s happening, so you’re not surprised by a second visit. Fast dispatch runs 7am to 7pm, Sunday through Friday.
- 4
Repair with the right materials. Depending on what’s needed, we use DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, or Copperfield products, matched to the job.
- 5
Final walkthrough. We show you what was done, what to watch for, and when the next sweep is due. Any follow-up is booked into the calendar.
How Much Does Chimney Repair Cost in Gresham?
Chimney repair in Gresham typically runs $250 – $5,500 depending on the work involved, with most common repairs in the $300 – $900 range. To break it down: a typical cap installation in Gresham runs $300 – $750, a flashing repair $400 – $900, a crown repair $350 – $800, and a full liner installation $2,800 – $5,500. Masonry repairs sit between $600 – $3,500 depending on how much of the chimney is affected.
What affects the price is mostly scope, not the calendar: how many flues are involved, the chimney’s height and roof pitch, whether the repair is a patch or a rebuild, and which materials are specified. A crown patch is a different job from a crown rebuild, and the estimate should always reflect the actual scope. How to avoid overpaying is simple: ask for the estimate in writing, ask which product line is being used, and don’t accept any recommendation for a repair or reline that isn’t backed by camera evidence you can see. If a repair can wait a season, we’ll say so rather than pressure a sale.
Our free estimate covers the inspection, the photo report, and a written scope of work. You’ll see the line items before any work begins, and the written estimate is what sets the final price.
Our Service Area Near Gresham
We work throughout Gresham and the surrounding east-side communities, including Fairview, Troutdale, Damascus, Sandy, Gladstone, and Oregon City. Scheduling across these towns usually fits within the same appointment window as a Gresham call, so nothing is delayed just because you live a few miles out. For nearby work, we also handle chimney repair north of the Columbia and Fairview to the west. We answer 24/7 if you need to get on the schedule.
Serving Gresham, OR – Our Local Coverage Area
We serve Gresham and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Gresham
Chimney repair is the work that fixes damage to a chimney’s flue, liner, crown, cap, flashing, or masonry. It covers everything from a new cap to a full liner installation, depending on what an inspection finds. In Gresham, the most common repairs are crown and flashing fixes after a wet winter. Call (833) 538-5519 for a free estimate.
Most chimney repairs in Gresham finish within a few hours to a full day, depending on the scope. A cap replacement or flashing repair is usually same-day work, while a full liner installation or masonry rebuild may take longer and can require a scheduled return. We give you the timeline in the written estimate. Call (833) 538-5519 to book an inspection.
Chimney repair in Gresham typically runs $250 – $5,500 depending on the work. Caps and crowns sit below $800, flashing is usually $400 – $900, and a full liner installation is $2,800 – $5,500. The written estimate sets the final price, and the estimate itself is free. Call (833) 538-5519 for an exact quote.
Yes. We install and service DuraFlex flexible liner systems, the professional standard for relined chimneys. If your flue needs relining, we’ll inspect it first and explain whether a full reline is needed or whether HeatShield resurfacing makes sense. Call (833) 538-5519 to schedule.
Same-day chimney repair is often possible in Gresham when the job is within a typical repair scope. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (833) 538-5519 to get on the schedule.
We stand behind the work we perform, and repair terms are confirmed in the written estimate before any work begins. If you have questions about what’s covered, ask before the job is scheduled so it’s all in writing. Call (833) 538-5519 and we’ll walk you through it.
Clear the area around the fireplace or stove and make sure we can reach the hearth and, if needed, the roof access. If you have a wood stove, let the fire go out at least a day before. Lock up pets and note any leaks or drafts you’ve noticed so we can inspect for them. Call (833) 538-5519 if you have questions.
Schedule Your Chimney Repair Service in Gresham Today
If something about your chimney doesn’t look right, it’s worth an inspection before the next burn season. Call (833) 538-5519 for a free estimate from Gresham Chimney Sweep. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get a photo report, a written scope of work, and a straight answer on what can wait and what can’t. No pressure, no surprise charges.
Written by the team at Gresham Chimney Sweep.