Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Repair Across Gladstone
If your chimney has cracked mortar, a failing crown, or a flue that smokes back into the room, we repair chimneys for Gladstone homeowners from the river blocks up into the older streets off Portland Avenue. This town is full of mid-century masonry fireplaces and wood stoves that were added or converted years ago, sometimes without a permit, and that history shapes how we work. We inspect before we quote, show you the camera footage, and fix what’s actually wrong. One call covers sweep, inspection, and repair. Call (833) 538-5519 for a free estimate.
Why Gladstone Homeowners Call Gresham Chimney Sweep for Chimney Repair
Gladstone is a small, older Clackamas County river town, and the chimney problems here are specific to it. Much of the housing predates modern code, so a routine sweep often turns into a masonry conversation before the first fall burn. We build the visit around that reality instead of treating every Gladstone house like a new build.
We work with an established roster of industry-recognized brands, so repairs use professional-grade materials, not whatever a generalist picked up at a hardware store. DuraFlex flexible liner systems, HeatShield resurfacing, and caps and components from Famco, Gelco, Olympia Chimney, and Copperfield all live in the same toolkit, which means we aim one repair at the whole system: flue, crown, cap, and chase together.
We answer 24/7 and offer fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 14 years of experience, and they’re trained on the camera work that tells a homeowner what’s really going on inside an old clay-tile flue. Nothing gets recommended here without footage you can watch yourself.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Flashing Repair in Gladstone
Chimney Flashing Repair in Gladstone usually comes down to the seam where the chimney meets the roof, and that seam takes a beating from our wet Willamette Valley winters. Flashing is the metal that seals that joint. When it rusts through, pulls loose, or was never installed right, rain runs down the masonry and into the attic or the smoke chamber. Most Gladstone flashing jobs run $300 – $900, with a typical repair around $450. We can work with your insurer when the damage traces back to a storm.
What Flashing Failure Looks Like
You’ll often see rust streaks on the chimney chase, water staining on the ceiling near the stack, or grit washing down the roof. In the older Gladstone blocks near the Clackamas River, decades of damp air speed that corrosion along. If the flashing is lifting off the shingles at the top edge, it’s time for a look before the next heavy rain.
Step Flashing and Counterflashing
The two-piece approach is standard here: step flashing woven into the shingles, then counterflashing cut into the masonry above it. Done well, the two layers shed water down the roof instead of into the wall. Replacing both at once costs a little more than patching one and lasts a great deal longer.
Chimney Crown Repair in Gladstone
Chimney Crown Repair in Gladstone is one of the most common jobs we quote, because the crown is the first thing our wet winters attack. The crown is the sloped concrete cap on top of the chimney. When it cracks, water gets into the masonry and the freeze-and-thaw cycle widens every gap. Crown repair typically runs $350 – $1,100 in Gladstone, depending on size and whether the crown can be resurfaced or needs to be recast. A full rebuild costs more, and we’ll tell you plainly when that’s the honest answer.
Why the Crown Cracks
Most crowns fail from hairline cracks that let in water, then spalling that opens them into real gaps. Once the water is inside, mortar joints below start to crumble and rusted dampers are the next thing a sweep finds. Sealing a crown that’s already broken just traps the moisture underneath.
Crown Repair vs. Rebuild
If the masonry below the crown is still sound, resurfacing restores the slope and drainage for a fraction of a rebuild. When the top courses of brick are spalled and loose, though, the crown comes off and those courses get rebuilt first. We let the camera and a close look on the roof decide which path we take.
Trusted Brands We Service in Gladstone
We work with the product lines the trade actually specifies: HeatShield for liner resurfacing, DuraFlex for flexible stainless relining, and Famco, Gelco, Olympia Chimney, and Copperfield for caps, dampers, and ventilation components. We don’t claim to stock parts locally; what matters is that we install the right professional-grade component and can get it in a reasonable turnaround. That’s the difference between a repair built for our damp river-valley climate and one that fails again in a couple of winters. If a brand isn’t right for your flue, we’ll tell you rather than force a fit.
Common Chimney Repair Problems We See in Gladstone Homes
- Cracked and spalled clay-tile liners. Decades of damp winters crack the original tiles and let creosote seep into the surrounding masonry. A camera inspection is the only honest way to see how far the damage runs.
- Wood stoves vented into fireplaces with no liner or an undersized flue. These setups draft poorly and build third-degree creosote fast. They need a properly sized liner before another fire is lit.
- Rusted-open dampers. A damper stuck open lets warm house air escape all summer and lets water in through the flue. Many Gladstone homeowners don’t notice until a sweep or inspection turns it up.
- Crumbling mortar around the firebox and smoke chamber. Damp river-valley air eats mortar joints for years before anything shows in the room. By the time you see it, a masonry repair is usually the right call.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Repair in Gladstone, OR
Here are typical ranges for work in Gladstone, so you can plan before anyone climbs on the roof. A chimney sweep and Level 1 inspection runs $150 – $300. Mortar repointing and tuckpointing, per section, runs $250 – $700. Spalling brick repair typically runs $400 – $900. Chimney waterproofing runs $300 – $650. Flashing repair runs $300 – $900. Crown repair runs $350 – $1,100, and a partial chimney rebuild can run $2,000 – $6,000 or more depending on height and how much masonry comes down. A HeatShield resurfacing job often lands in the $1,200 – $2,800 range, while a full DuraFlex reline runs $2,500 – $5,500. These are estimates, not a quote. The written estimate sets the final price, and you get it in writing before any work begins.
We Also Serve Cities Near Gladstone
Gladstone sits at the edge of the Portland metro, and we take chimney repair to the towns around it too: West Linn, Oregon City, Damascus, and Tualatin all share the same wet Willamette Valley conditions that wear down old masonry. If you’re in one of these neighbors and your chimney needs a look, call us and we’ll book a visit.
Serving Gladstone, OR – Our Local Coverage Area
We serve Gladstone and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Chimney Repair in Gladstone
Yes. A Level 2 inspection with a camera is what you need before any sweep when a stove or insert was added without paperwork. A qualified local pro runs the camera first, shows you the footage, and only then recommends relining with a product like HeatShield or DuraFlex. Old Gladstone homes with unlined or clay-tile flues are exactly where that footage matters most. Call (833) 538-5519 for an exact quote; estimates are free.
Repeated wetting and drying is the cause. The crown absorbs rainwater, then the freeze-and-thaw cycle opens the hairline cracks into real gaps. A resurfaced or recast crown with proper slope sheds that water instead of holding it. If yours keeps cracking, it’s likely been patched over a crack rather than repaired. Call (833) 538-5519 for an exact quote; estimates are free.
Only a camera inspection can tell you that for certain. Third-degree creosote is glazed, hard, and fused to the flue wall, and it doesn’t scrape off like the soft, flaky layer a sweep clears. Wood stoves and inserts venting into undersized flues build it fast. We show you the footage so you can see it yourself. Call (833) 538-5519 for an exact quote; estimates are free.
It’s usually a damper replacement, but it’s worth checking as part of a repair visit. In Gladstone’s older river blocks, dampers rust open from years of damp air, and while a sweep is up there it often finds the water damage behind it. We replace the damper with a proper component and flag anything else the camera catches. Call (833) 538-5519 for an exact quote; estimates are free.
No. Age alone isn’t a reason to reline. We recommend it only when the camera shows cracked or spalled tiles letting creosote into the masonry, or when a stove or insert is venting into an undersized flue. If your flue is sound, we’ll tell you and save you the money. Call (833) 538-5519 for an exact quote; estimates are free.
Book Your Gladstone Chimney Repair
Gladstone’s old river-valley chimneys don’t need a sweep-and-go. They need a camera, an honest look, and a repair built for our damp climate. One call covers sweep, inspection, and repair, and nothing is recommended without footage you can watch yourself. Call (833) 538-5519 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gresham Chimney Sweep.